Trik-trik kode HP

[willydewi]

Here *** ALL THE SECRET CODES *** 4 all gsm
for sumsung

*#9998*228# : Battery status (capacity, voltage, temperature)
*#9998*246# : Program status
*#9998*289# : Change Alarm Buzzer Frequency
*#9998*324# : Debug screens
*#9998*364# : Watchdog
*#9998*377# : EEPROM Error Stack - Use side keys to select values. Cancel and ok.
*#9998*427# : Trace Watchdog
*#9998*523# : Change LCD contrast - Only with version G60RL01W
*#9998*544# : Jig detect
*#9998*636# : Memory status
*#9998*746# : SIM File Size
*#9998*778# : SIM Service Table
*#9998*785# : RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error.
*#9998*786# : Run, Last UP, Last DOWN
*#9998*837# : Software Version
*#9998*842# : Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.
*#9998*862# : Vocoder Reg - Normal, Earphone or carkit can be selected
*#9998*872# : Diag
*#9998*947# : Reset On Fatal Error
*#9998*999# : Last/Chk

*#9998*9266# : Yann debug screen (=Debug Screens?)
*#9998*9999# : Software version

If the up Codes doesn't work, you should change *#9998* to *#0. i.e. *#9998*523# change to *#0523#. An other thing that will help is to remove your SIM card. *0001*s*f*t# : Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# : unknown
*0003*?# : unknown

SP-unlock SGH-600 (and also SGH-Sgh-600)
*2767*3855# : Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0. (Doing this is illegal)

*2767*2878# : Custom EEEPROM Reset

*These codes have been tested with version FLD_2C6 G60SB03X of Samsung SGH-600

for d500

*#11[quote]11# S/W Version
*#1234# Firmware Version
*#2222# H/W Version
*#8999*8376263# All Versions Together

*#8999*8378# Test Menu
*#4777*8665# GPSR Tool
*#8999*523# LCD Brightness
*#8999*377# Error Menu
*#8999*327# EEP Menu
*#8999*3825523# Don't Know.
*#8999*667# Debug Mode
*#92782# PhoneModel (Wap)
#*5737425# JAVA Mode
*#2255# Call List
*#232337# Bluetooth MAC Adress
*#5282837# Java Version

#*4773# Incremental Redundancy
#*7752# 8 PSK uplink capability bit
#*7785# Reset wakeup & RTK timer cariables/variables
#*1200# ????
#*7200# Tone Generator Mute
#*3888# BLUETOOTH Test mode
#*#8999*324# ??
#*7828# Task screen
#*5111# ??
#*#8377466# S/W Version & H/W Version
#*2562# Restarts Phone
#*2565# No Blocking? General Defense.
#*3353# General Defense, Code Erased.
#*3837# Phone Hangs on White screen
#*3849# Restarts Phone
#*3851# Restarts Phone
#*3876# Restarts Phone
#*7222# Operation Typ: (Class C GSM)
#*7224# !!! ERROR !!!
#*7252# Operation Typ: (Class B GPRS)
#*7271# CMD: (Not Available)
#*7274# CMD: (Not Available)
#*7337# Restarts Phone (Resets Wap Settings)
#*2787# CRTP ON/OFF
#*2886# AutoAnswer ON/OFF
#*3737# L1 AFC
#*5133# L1 HO Data
#*7288# GPRS Detached/Attached
#*7287# GPRS Attached
#*7666# White Screen
#*7693# Sleep Deactivate/Activate
#*7284# L1 HO Data
#*2256# Calibration info? (For CMD set DEBUGAUTONOMY in cihard.opt)
#*2286# Databattery
#*2527# GPRS switching set to (Class 4, 8, 9, 10)
#*2679# Copycat feature Activa/Deactivate
#*3940# External looptest 9600 bps
#*4263# Handsfree mode Activate/Deactivate
#*4700# Please use function 2637
#*7352# BVMC Reg value (LOW_SWTOFF, NOMINAL_SWTOFF)
#*2558# Time ON
#*3370# Same as 4700
#*3941# External looptest 115200 bps
#*5176# L1 Sleep
#*7462# SIM Phase
#*7983# Voltage/Freq
#*7986# Voltage
#*8466# Old Time
#*2255# Call Failed
#*5187# L1C2G trace Activate/Deactivate
#*5376# DELETE ALL SMS!!!!
#*6837# Official Software Version: (0003000016000702)
#*7524# KCGPRS: (FF FF FF FF FF FF FF FF 07)
#*7562# LOCI GPRS: (FF FF FF FF FF FF FF FF FF FF FF FE FF 01)
#*2337# Permanent Registration Beep
#*2474# Charging Duration
#*2834# Audio Path (Handsfree)
#*3270# DCS Support Activate/Deactivate
#*3282# Data Activate/Deactivate
#*3476# EGSM Activate/Deactivate
#*3676# FORMAT FLASH VOLUME!!!
#*4760# GSM Activate/Deactivate
#*4864# White Screen
#*5171# L1P1
#*5172# L1P2
#*5173# L1P3
#*7326# Accessory
#*7683# Sleep variable
#*8465# Time in L1
#*2252# Current CAL
#*2836# AVDDSS Management Activate/Deactivate
#*3877# Dump of SPY trace
#*7728# RSAV
#*2677# Same as 4700
#*3797# Blinks 3D030300 in RED
#*3728# Time 2 Decod
#*3725# B4 last off
#*7372# Resetting the time to DPB variables
#*7732# Packet flow context bit Activate/Deactivate
#*6833# New uplink establishment Activate/Deactivate
#*3273# EGPRS multislot (Class 4, 8, 9, 10)
#*7722# RLC bitmap compression Activate/Deactivate
#*2351# Blinks 1347E201 in RED
#*4472# Hysteresis of serving cell: 3 dB
#*2775# Switch to 2 inner speaker
#*9270# Force WBS
#*7878# FirstStartup (0=NO, 1=YES)
#*3757# DSL UART speed set to (LOW, HIGH)
#*8726# Switches USBACM to Normal
#*8724# Switches USBACM to Generator mode
#*8727# Switches USBACM to Slink mode
#*8725# Switches USBACM to Loop-back mode
#*3838# Blinks 3D030300 in RED
#*2077# GPRS Switch
#*2027# GPRS Switch
#*0227# GPRS Switch
#*0277# GPRS Switch
#*22671# AMR REC START
#*22672# Stop AMR REC (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# Pause REC
#*22674# Resume REC
#*22675# AMR Playback
#*22676# AMR Stop Play
#*22677# Pause Play
#*22678# Resume Play
#*77261# PCM Rec Req
#*77262# Stop PCM Rec
#*77263# PCM Playback
#*77264# PCM Stop Play
#*2872# CNT
*#8999*283# ???
#*22679# AMR Get Time
*288666# ???
*2886633# ???
*#8999*364# Watchdog
__________________


nokia cdma

*#775738# Pri Seting (enable/disable)

*3001#12345#

LG CDMA SECRETS CODES

Field Test MENU > 0 > 000000 > Field Test Other Programming Secrets:

LGC-300 programming:

menu + 9 and enter SPC: "000000" or may be other SPC typed by user. A-Key: press STO for some time while you can see special code enter zone. Type 2539** and enter A-key

LGC-330W programming:

menu + 4 + 0 and enter SPC: "000000" or may be other SPC typed by user. A-Key: type 2539** and enter A-key

LGC-800W /500 programming:

menu + 0 and enter SPC: "000000" or may be other SPC typed by user. A-Key: type 2539** and enter A-key

LGC-510 programming:

menu + 3 + 0 and enter SPC: "000000" or may be other SPC typed by user. A-Key: type 2539** and enter A-key

LG1010, LG4NE1, TP2200, TP2100, Touchpoint, SB/DB, TP1100 and TP5200

Press ## Enter the OTKSL Scroll to SAVE and press OK Scroll to MIN and press OK Enter 10 digit MIN scroll to SAVE and press OK Scroll to SID and press OK (Skip on 4NE1 go to RESET PHONE and press OK to complete) Enter SID (4654) and scroll to SAVE and press OK Programming is complete

LG5350

Enter ## and enter the OTKSL and press the left soft key under the word “Save” At the Service Program display select Mobile Phone # and press the OK in the center of the 4 way navigation key Enter the 10 digit MIN and press OK Scroll down to 4. Advanced and press OK Scroll to NMSI and press OK Enter the MSID and press OK Scroll down to 9. Amps Phone # and press OK Enter the MSID and press OK

Press the END key


MOTOROLA PROGRAMING CODES

Analog Models

Changing the Banner: #PROGRAM# or [Fcn] 0000000000000 (13 0's)

Field Test: [Fcn] 0 0 * * TESTMODE [Sto]

Reset Timers: Follow the Field Test procedure above and then #32#

Alternative Programming Menu: #55#

(Not sure): # [SID code]#* SEND

Programming of various other models:

V60c Programming Mode:

74663 # [Menu] [Menu] (you will need the programming code)

Field Test: [Menu] 073887 * (you will need the security code -- try 000000)

To deactivate field test: Power phone up, hit MENU and the left button (should bring up the menu). There's a menu option for test-mode and at this point you can turn the menu off and return the phone to normal. Alternatively press menu and then the nearest button to the left (Phone book button) quickly and it will take you back to the main screen and your phone will look normal.

StarTac 7790

Field Test: [Fcn] 0 0 * * TESTMODE [Sto]

StarTac 7760, 7860

Field Test: [Fcn] 0 0 * * TESTMODE [Sto] Service Menu: [Fcn] 0 000000 000000 RCL

Complete system test (most models): (Phone OFF), Hold down any row of keys (1+2+3, 4+5+6, etc) and turn the phone ON

To access the diagnostic mode on the I30: #, *, MENU, JOYSTICK-RIGHT (Do these keystrokes fast)

To access the diagnostic mode on any of the older iDEN phones (pre-i1000): VOLUME DOWN, MENU, MENU, MENU, LEFT, MENU, MENU, LEFT (this is the reverse of the test menu routine)

To access the diagnostic mode on any of the new models (i1000+, i700+, i550+, etc): Hold down any three keys in a row across.

The unit will enter the test mode and can be stepped through the various functions with the keys and buttons. At the end of the test, power cycle the unit to return to normal function. This test will check various phone functions, including LCD display, speaker, earphone, microphone, LEDs, vibrator, backlight and all of the buttons and keys for the newer models


SAMSUNG CDMA SECET CODES

Older Models:

NAM Programming: 47*869#08#9

Test mode: *759#813580 OR 5809540*45680

Exit Test Mode: 02 A-Key: menu + 0,

code 25##

Samsung SPH-T100

MENU 820 > 810325

Samsung SCH-3500

MENU 820 > 295184

Programming of various other models:

Samsung A500

Enter ## and the 6 digitOTKSL

SERVICE MENU will appear and 1.Basic will be highlighted

Press OK Device will display NAM CDMA/ Phone Number

Enter 10 digit MIN Press OK (3 times) Display will return to Service Menu.

Press END. Programming is complete

Samsung N240 and N400

Enter ## and type in the 6 digit OTKSL

The display will show SVC MENU and 1. Phone Number

Press OK Enter the 10 digit MIN and press OK

The display will show NAM with Home SID on the second line (Note: SID is no longer used)

Press OK

The display will return to the SVC MENU

Press END to complete the programming


Samsung N300

Press ## followed by the OTKSL
SVC menu will be displayed
Press 1 for Phone #
Enter the 10 digit MIN and press OK
MIN that was entered will be displayed press OK
SVC Menu will display press 3 for NAM
Enter the 4 digit Home SID press OK
Press END and handset will power cycle

Samsung i300
Tap on the Phone Icon with stylus
Press #907*9#0 ENTER LOCK should appear on screen
ENTER OTKSL
SVC MENU will appear press 1
Enter 10 digit MIN and then press SAVE
Press SAVE again
Press 3 and then press SAVE 6 times
Enter the HOME SID and press SAVE once
Press END key twice

Samsung A400 and A460
Enter ## and OTKSL
Press 1 for Basic at MENU (1 of Phone # when using the MSL)
Enter 10 digit MIN and press OK
At 1.Basic Menu press the END key
Handset will power cycle

Samsung 3500, 8500, 6100, and N200
Press MENU
Press 6 0 (3500) 8 2 0 (8500/6100/N200)
Enter OTKSL
Press 1 at SVC MENU Screen
Enter MIN and press OK
Press OK 4 times
Enter SID (4654) and press OK
Press END key
Programming is complete


gsm NOKIA SECRET CODES

Nokia CodesThese Nokia codes will work on most Nokia mobile phones, however we accept no responsibility of any kind for damage done to your phone whilst trying these Nokia secret codes.

Nokia code Code function

*3370# This Nokia code activates Enhanced Full Rate Codec (EFR) - Your Nokia cell phone uses the best sound quality but talk time is reduced my approx. 5%

#3370# Deactivate Enhanced Full Rate Codec (EFR)

*#4720# Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time

*#4720# With this Nokia code you can deactivate the Half Rate Codec

*#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type

*#9999# Phones software version if *#0000# does not work *#06# For checking the International Mobile Equipment Identity (IMEI Number)

#pw+1234567890+1# Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+2# Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+3# Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

#pw+1234567890+4# SIM Card Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

GSM SAMSUNG SECRET CODES

*#06# -> Show IMEI

*#9999# -> Show Software version

*#0837# -> Show Software Version (instructions)

*#0001# -> Show Serial Parameters

*#9125# -> Activates the smiley when charging.

*#9998*228# -> Battery status (capacity, voltage, temperature)

*#9998*246# -> Program status

*#9998*289# -> Change Alarm Buzzer Frequency

*#9998*324# -> Debug screenslect values. Cancel and ok.

*#9998*427# -> Trace Watchdog

*#9998*523# -> Change LCD contrast - Only with version G60RL01W

*#9998*544# -> Jig detectService Table

*#9998*785# -> RTK (Run Time Kernel) errors - if ok then phn is reset, info is put inmemory error.

*#9998*786# -> Run, Last UP, Last DOWN

*#9998*837# -> Software Version

*#9998*842# -> Test Vibrator - Flash the screenligth during 10 seconds and vibrationactivated.

*#9998*862# -> Vocoder Reg - Normal, Earphone or carkit can be selected

*#9998*872# -> Diag

*#9998*947# -> Reset On Fatal Error

*#9998*999# -> Last/Chk

*#9998*9266# -> Yann debug screen (=Debug Screens?)

*#9998*9999# -> Software version

*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)

*0002*?# -> unknown

*0003*?# -> unknown SP-unlock SGH-600 and SGH 2100

*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! ) But also changes IMEI to 447967-89-400044-0

*2767*2878# -> Custom EEEPROM Reset These codes has been tested with version FLD_2C6 G60SB03X of Samsung SGH-600 type 8889 instead of 9998.


GSM MOTOROLA SECRET MOBILE CODES

Motorola

IMEI number: * # 0 6#
Net Monitor ON: * * * 1 1 3 * 1 * [OK]
Net Monitor OFF: * * * 1 1 3 * 1 * [OK]
* - press this until box shown up

To activate RBS:

(pause means the * key held in until box appears)

[pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]

You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

To de-activate RBS,

[pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]

This only works with some versions of software. Please report what works and doesn't for you.

Reported working, by country:

d460: IT
6200 Flare: UK (Orange), AU
7500: IT (model: F16 HW: 5.2 SW: 2.1)
8200: ES, AU, NL, BE
8400: IT, NL
8700: AU, IT, SG, DE, ES, ZA
Uses of RBS:

Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

SONY ERICSSON SECRET CODE

General Secrets

IMEI (International Mobile Equipment Identity): *#06#

Firmware Version: >*<<*<*

Programming Checks: >*<<*<*> or >*<<*<*>


Accessing the phone without a SIM card: **04*0000*0000*0000# then on 'Wrong Pin' No


Reset English Menu: *#0000#


300, 600, 700 Series


Programming Menu (Short): 987 + >


Programming Menu (Long): 923885 + >


Field Test: 904090 + > (to exit 904090 + >)


Phone Test: 904059 + > (to exit 3 + <)


Phone Reset: 904060 + >


CDMA Mode: 904093 + menu


Analog Mode: 904095 + menu DM mode 904959 + menu


GSM PHILIPS SECRET CODES

Philips GENIE


To view IMEI number *#06#

*#2254*# is the statusregister: C, BS, RR, MMI, CREAT.

*#2255*# will activate and deactivate the "DEBUG CALL"-Mode

*#2558*# will display the time in days,hours and minutes you are connected to the GSM network

To force a reconnection to the network, type : *#2562*#

To view and modify the Security Code of the phone, type: *#7489*#

To view some info about your SIM card like the phase level, the name, type: *#7378*#

To obtain information on SIM lock, Init and Flags, press: *#3377*#

To activate or deactivate Sleep Mode: *#7693*#

To get info about Sleep Mode: *#8463*#


Philips FIZZ
IMEI: *#06#

Lock Code: *#1234#

Software Version
To find software version, enter *#8377*#

The output will look something like:

Version : 0916 - EEPROM : 00000000-00 - TDA : 2445 - KISS : 0502 SIM-LCK

..or extended software version *#5644*#

output:

Version : 09162205 - EEPROM : 00000000-00 - TDA : 2445 - KISS : 0502 SIM-LCK

SM ALCATEL SECRET MOBILE CODES

ALCATEL

* # 0 6 # : IMEI number
* # 0 6 # : Software version
0 0 0 0 0 0 * : Net Monitor

PINOUTS AND CODES FOR PANASONIC MOBILES

Panasonic G500

IEMI:
To view IMEI number *#06#


--------------------------------------------------------------------------------

PINOUTS

1 - Ground
2 - TX_Audio
3 - Audio_Ground
4 - HF_ON (L=ON) -> L=H/F ON
5 - AOP_Sense <- Data Adaptor Select
6 - Serial_Up <- UART up (9600,33.8kbps)
7 - Serial_Down -> UART down
8 - External_Power <- POWER FOR CHARGING
9 - Ground
10 - RX_Audio
11 - Radio_Mute -> L=MUTE
12 - HF_Sense <- L=H/F MODE
13 - Reserved L=FLASH WRITE ENABLE
14 - Ignition <- H=ON
15 - Logic_Power -> H=HANDSET ON
16 - PAON -> Power Amplifier Control Signal.

************************************************** **
Nokia 3310 Secret codes
Jul, 08 2003 - 06:20
contributed by: mef
*#06# To find IMEI (International Mobile Equipment Identity)

*#7780# Restores Factory Settings..(Memory, language, counters not included)

*#3110# For checking the phone's software (SW) - called firmware revision information.

*#746025625# [*#sim0clock#] To check if the Sim-Clock can be Stopped (Sim-clock-stop is a kind of standby mode which will save battery time)

*#92702689# [*#war0anty#] Phone asks 'warranty code:'

6232 (OK) Displays the Month and Year of Manufacture

9268 (OK) Displays Serial Number

7332 (OK) Displays the date of the last repairment - if found

7832 (OK) Displays (if found) the date where the phone was purchased

37832 (OK) Set the Purchasing Date MMYY (This date can be set only once!)

87267 (OK) Transfers ALL phone numbers, Logo's, and ringtones from other gsm phones

Nokia 101 cell phone lockcode
Jul, 10 2000 - 02:35
Nokia 101 cell phones set up by Bell Mobility in Toronto can have their lock code circumvented by the following method:

Type: * 3001 # 12345 [STO] 00
Wait for: NOT DONE
Type: [RCL] 01


Clear old lock code (the last four digits) and enter a new lock code. Be very careful not to delete other characters.

Type: [STO] 01 [STO]
Turn power off.

Nokia 9000/9000i
Nov, 25 2000 - 22:41
To view IMEI number *#06#
To view Software Version enter *#8110# Latest Version is under Phone Info.
To view Week and Year of manufacture enter *#3283#

Samsung SGH-600 / SGH-2100
Secret Codes

*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0837# -> Show Software Version (instructions)
*#0001# -> Show Serial Parameters
*#9125# -> Activates the smiley when charging.

*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack - Use side keys to select values. Cancel and ok.
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast - Only with version G60RL01W
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error. *#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.
*#9998*862# -> Vocoder Reg - Normal, Earphone or carkit can be selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk

*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version

*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown

SP-unlock SGH-600 and SGH 2100

*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0, To restore your old IMEI use the IMEI program found on the software page.

*2767*2878# -> Custom EEEPROM Reset

These codes has been tested with version FLD_2C6 G60SB03X of Samsung SGH-600

Samsung 811
Jul, 08 2000 - 01:24
47*869#08#9

- unlock code / change roaming code / ID


SIEMENS S1 / S3 / S3 COM / S4

To view the software date and else with S3 com, S4, S4Power
press with SIM removed *#06# and left softkey.

To view some other stuff with S4Power
press with SIM removed *#06# and left softkey twice.

To view the software date with S3 com, S4, S4Power
press with SIM installed menu 98 and left softkey twice.

ACTIVATE MONITOR MODE

Siemens S1/S3

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key),
5553756, HangUp Button (Red HandSet key)

Siemens S3 COM/S4

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button
(left MENU key), 7684666, HangUp Button (Red HandSet key)

Note: Now Monitor should appear at the bottom of the Network Options menu.

MONITOR MODE

Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Pressing the right Display Button when in monitor mode will show a
list of the six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )

CH Channel Number

RX Signal Strength (dB)

N NCC (Colour Code)

B BCC (Colour Code)

CI Cell ID (in Hex)

C1+ How long before phone does forced hand over.(see RX and RXAM)

LAI Location Area Identity. Display Network ID code(42F010 = 240.01) and MSC

TXPWR Transmit Power (dB)

RXAM Receive signal strength cut-off point

TS* Time Slot Number

TA* Timing Advance. Distance from tower in Km X 2

PL* Power Level
SIEMENS S1

Here's a trick to play Tetris, also known as Klotz on a Siemens S1.
Turn the phone on. Enter PIN. Before the telephone has logged in to the
your GSM net do the following steps.

1: Choose F 9 (function settings)
2: Choose send own number and push the right button for choose.
3: Push 9

USE 2 as < and 8 as > , rotate the klotz with 5 and drop with 4.

I have just heard from one of the programmers of the phone that Tetris
was in the phone during development, but it was removed before it was produced.
Apparantly someone has the patent on games in mobile phones and Siemens
didn't want to pay the licensing fees. It was either in Menu F-9-9 or it's not there at all


Siemens C 25

Secret Codes

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO


Sagem MC959

Secret Codes

MC959

in main menu press * for hot-menu:
lcd, led, vibra, tests, imei, software versions, battery voltage

Type MENU - 5 - 1 - 1 - # to enter Engineering menu on SAGEM (RC-712, 721, 815 and 815 plus) phones.

Panasonic G500

IEMI:
To view IMEI number *#06#


--------------------------------------------------------------------------------

PINOUTS

1 - Ground
2 - TX_Audio
3 - Audio_Ground
4 - HF_ON (L=ON) -> L=H/F ON
5 - AOP_Sense <- Data Adaptor Select
6 - Serial_Up <- UART up (9600,33.8kbps)
7 - Serial_Down -> UART down
8 - External_Power <- POWER FOR CHARGING
9 - Ground
10 - RX_Audio
11 - Radio_Mute -> L=MUTE
12 - HF_Sense <- L=H/F MODE
13 - Reserved L=FLASH WRITE ENABLE
14 - Ignition <- H=ON
15 - Logic_Power -> H=HANDSET ON
16 - PAON -> Power Amplifier Control Signal.

Mitsubishi MT- D30

Secret Codes

Monitor mode: Hold C and press 379
Secret menu: Hold C and press 987
Version number: Hold C and press 597
Phase1 and 2 : Hold C and press 499
Warm start : Hold C and press 179
Instant turn off: Hold C and press 999
Unlock menu: Hold C and press 787090

Mitsubishi Trium

*#0000# to reset the phones menu-language to natural language, set initially by the distributor.

*#06# for checking the IMEI (International Mobile Equipment Identity)

hold * then 5806 - show software version
hold * then 5807 - a littel bit diffrent
hold * then 5472 - Testmode for datacable (it seems so)
hold * then 4329 - Activate and deactivate NETMONITOR
hold * then 621342 - Activate and deactivate another NETMONITOR
hold * then 3926 - shutdown

SP lock
You can turn around the lock routin by entering **04*PIN*PIN*PIN# now the secretcode change was applied and the software turns back to main menue. It works not on all triums, only on thos with older sofware versions


SIEMENS S1 / S3 / S3 COM / S4

To view the software date and else with S3 com, S4, S4Power
press with SIM removed *#06# and left softkey.

To view some other stuff with S4Power
press with SIM removed *#06# and left softkey twice.

To view the software date with S3 com, S4, S4Power
press with SIM installed menu 98 and left softkey twice.

ACTIVATE MONITOR MODE

Siemens S1/S3

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key),
5553756, HangUp Button (Red HandSet key)

Siemens S3 COM/S4

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button
(left MENU key), 7684666, HangUp Button (Red HandSet key)

Note: Now Monitor should appear at the bottom of the Network Options menu.

MONITOR MODE

Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Pressing the right Display Button when in monitor mode will show a
list of the six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )

CH Channel Number

RX Signal Strength (dB)

N NCC (Colour Code)

B BCC (Colour Code)

CI Cell ID (in Hex)

C1+ How long before phone does forced hand over.(see RX and RXAM)

LAI Location Area Identity. Display Network ID code(42F010 = 240.01) and MSC

TXPWR Transmit Power (dB)

RXAM Receive signal strength cut-off point

TS* Time Slot Number

TA* Timing Advance. Distance from tower in Km X 2

PL* Power Level
SIEMENS S1

Here's a trick to play Tetris, also known as Klotz on a Siemens S1.
Turn the phone on. Enter PIN. Before the telephone has logged in to the
your GSM net do the following steps.

1: Choose F 9 (function settings)
2: Choose send own number and push the right button for choose.
3: Push 9

USE 2 as < and 8 as > , rotate the klotz with 5 and drop with 4.


NEW CODE

Alcatel
Master Codes
- 25228352
- 25228353
- 83227423 (TH3/4,BH4,BF5,BG3,BF3/4..)

###337*07# - master reset (with SIM)
###847# - factory reset (with SIM)
###728# - factory reset (with SIM)

Alcatel 835 formating - **0102#



Samsung
*2767*3855# - FULL E2P RESET
*2767*2878# - CUSTOM E2P RESET
#*7337# - UNLOCK
*2767*688# - UNLOCK
*#0523# - CONTRAST
*#9998*523# - CONTRAST
*#8999*8378# - Service Menu (X100)


Philips

#20021208# ok - 630 without SIM (erase flash)
*#7728*# - RSAV DONE
*#3849*# - ??? reboot
*#3851*# - ??? reboot
Philips 568 *01763*737381# - reset


Pantech
*01763*737381# - master reset (user data, user code) without SIM
*01763*8371# - SW version
*01763*6371# - UNLOCK
*01763*3641# - Menu


Panasonic

*01763*737381# - master reset (user data, user code) A100, A101, A102,G50, G51, G70, GD55..
*369# - MENU

7, 4, 6, menu, menu - lock menu
*#9999# - 5 sec after power on - SW version (GD75, GD67, GD87..)


LG
2945#*# - service menu (code reset)(W3000 G5300 C1200 G7100...)
2945#- hold (LG 500,600)
B1200 *+pwr, 6,6,8 Service Menu
B1300 *+pwr, 1,5,9 Service Menu

Security Removing Code For Lg 8110,8120.
47328545454#
Or
277634#*#


Sony-Ericsson
> * < < * < * - Service menu

< * * < - Lock menu


VK Mobile

*#79# - SW version
*#85*364# - hold menu
855855# without SIM (VG107)
85558555#-hold
4268#-hold (VG207)



Voxtel
0124 - master code
0718#- hold - menu (ST11, SC10, V100 without SIM)
4268#- hold - show code (ST11, SC10 without SIM)
*789(#)- hold - menu (V50, V300, RX100 without SIM)



Motorola
(T190, T191, T205) master code

- 19980722

- 20010903

**********

P2K test menu:
*#06#, menu, menu, 048263*

Test comands:
32*116*1*0*0 - read phone code
32*118*1*0*0 - read security code
18*0 - factory reset, phone code off
18*1 - master reset
54*18*1 - full phone reset
10*0*6 - select 900/1800
32*279*1*0*8 - model
32*383*1*0*0 - flex version

Hard reset MPX200, MPX220 - blue button + power on


Nokia
*#7370925538# (valet code reset) 6230
*#746025625# [*#sim0clock#]
*#92702689# [*#war0anty#]


Fly Bird
S688 - #*301#02# send - with SIM
menu:
7 - 10 - ok,

#*8000#, #*3676# (reboot repair)

V09, S1180 - *, 3 times down, 3 times up - service menu


Enol
*#987*00# - Service menu
*#987*99# - Full reset
*#900# - SW version


Maxon
*#9922# - menu, reset (without SIM)
*#9900# - Software Version
*#9901# - Software Version (PBatch)




S60 Siries (SX1, 6600, N-Gage..)
*#7780# - factory default
*#7370# - full factory defaults (all user data reset)
SX1 formating - * + # + power on
6600 formating - 3 + * + send + power on
Sendo X1 formating - 5 + power on


Mitsubishi
*65512890 (*-hold) format FFS (Eclipse)

* 3926 - (*-hold) test mode

* 5806 - (*-hold) SW version

*(hold) 787090 - trium 320 unlock menu


Huawei (cdma)

MASTER SECURITY CODE
-309296
-3092
-9296


Pantech HX-550C (cdma)

Full reset (phone code reset)- ##03*934#9367*192#397#7412569746 PWR,
after reset - ##27732726 PWR and select "with uim"



Audiovox 107 45680*47*869#1
Audiovox 120 #86904**89397#
Audiovox 130,100,8300,8600 ##20022002"END"1
AUDIVOX 7900 MENU#ПИСЬМО*1 10СЕК
Audiovox 4000,9500 289F#1
CyberBell 100 ##1475369908##"save"
Ericsson 923885"Menu"
EVRC #763*FF
GTRAN GCP-2000 01#737
Hunday-110 #86904**89397#
Hunday-600 ##20022002"END"1 код 100499
LG-300 "Menu" 9
LG-330 "Menu" 40
LG CX300V Menu 0
LG-800 "Menu" 0

Programming:

Samsung
All type of phones (old modeles):
NAM programming: 47*869#08#9
Test mode: *759#813580 or 5809540*45680
exit test mode - 02
A-Key: menu + 0, code 25##

Samsung A500
1. Enter ## and the 6 digit OTKSL
2. SERVICE MENU will appear and 1.Basic will be highlighted
3. Press OK
4. Device will display NAM CDMA/ Phone Number
5. Enter 10 digit MIN
6. Press OK (3 times)
7. Display will return to Service Menu. Press END.
8. Programming is complete

Samsung N240 and N400
1. Enter ## and type in the 6 digit OTKSL
2. The display will show SVC MENU and 1. Phone Number
3. Press OK
4. Enter the 10 digit MIN and press OK
5. The display will show NAM with Home SID on the second line (Note: SID is no longer used)
6. Press OK
7. The display will return to the SVC MENU
8. Press END to complete the programming

Samsung Uproar
1. Press MENU key
2. Enter 9 2 0
3. Enter the OTKSL
4. At SVC Menu screen press OK
5. Enter MIN and press OK 4 times
6. Enter SID (4654) and press OK
7. Press END key
8. Programming is complete

Samsung N300
1. Press ## followed by the OTKSL
2. SVC menu will be displayed
3. Press 1 for Phone #
4. Enter the 10 digit MIN and press OK
5. MIN that was entered will be displayed press OK
6. SVC Menu will display press 3 for NAM
7. Enter the 4 digit Home SID press OK
8. Press END and handset will power cycle

Samsung i300
1. Tap on the Phone Icon with stylus
2. Press #907*9#0 ENTER LOCK should appear on screen
3. ENTER OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE 6 times
8. Enter the HOME SID and press SAVE once
9. Press END key twice

Samsung A400 and A460
1. Enter ## and OTKSL
2. Press 1 for Basic at MENU (1 of Phone # when using the MSL)
3. Enter 10 digit MIN and press OK
4. At 1.Basic Menu press the END key
5. Handset will power cycle

Samsung 3500 8500 6100 N200
1. Press MENU
2. Press 6 0 (3500) 8 2 0 (8500/6100/N200)
3. Enter OTKSL
4. Press 1 at SVC MENU Screen
5. Enter MIN and press OK
6. Press OK 4 times
7. Enter SID (4654) and press OK
8. Press END key
9. Programming is complete

Qualcomm
QCP-800 programming: menu + 3 + 0.
SPC: "000000" or may be other SPC typed by user.
QCP-820/1920/2035: type "111111" and press Jog Dial.
Choose "Programming" and enter SPC: "000000" or may be other SPC typed by user.
QCP 1960 and 2760
1. Press softkey under the work MENU
2. Press 8 0
3. Enter the OTKSL
4. Press softkey for OK
5. Enter MIN and press softkey for OK
6. No SID is require for this handset
7. Press softkey for EXIT
8. Programming is complete

LG
LGC-300 programming: menu + 9 and enter SPC: "000000" or may be other SPC typed by user
A-Key: press STO for some time while you can see special code enter zone. Type 2539** and enter A-key
LGC-330W programming: menu + 4 + 0 and enter SPC: "000000" or may be other SPC typed by user.
A-Key: type 2539** and enter A-key
LGC-800W /500 programming: menu + 0 and enter SPC: "000000" or may be other SPC typed by user.
A-Key: type 2539** and enter A-key
LGC-510 programming: menu + 3 + 0 and enter SPC: "000000" or may be other SPC typed by user.
A-Key: type 2539** and enter A-key

LG1010 LG4NE1 TP2200 TP2100 Touchpoint SB/DB TP 1100 TP5200
1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. Scroll to MIN and press OK
5. Enter 10 digit MIN scroll to SAVE and press OK
6. Scroll to SID and press OK (Skip on 4NE1 go to RESET PHONE and press OK to complete)
7. Enter SID (4654) and scroll to SAVE and press OK
8. Programming is complete

LG5350
1. Enter ## and enter the OTKSL and press the left soft key under the word “Save”
2. At the Service Program display select Mobile Phone # and press the OK in the center of the 4 way navigation key
3. Enter the 10 digit MIN and press OK
4. Scroll down to 4. Advanced and press OK
5. Scroll to NMSI and press OK
6. Enter the MSID and press OK
7. Scroll down to 9. Amps Phone # and press OK
8. Enter the MSID and press OK
9. Press the END key

TP 2100
1. Press ##
2. Enter OTKSL
3. Scroll to SAVE and press Roller Ball in for OK (ESN will display)
4. Select NEXT (by pressing in the roller ball)
5. Scroll to EDIT and press in the roller ball
6. Enter MIN
7. Scroll to SAVE and press roller ball in
8. Select NEXT at the next 3 screens and then EXIT
9. Programming is complete

TP3000
1. Press ##
2. Enter OTKSL
3. Scroll to SAVE and press OK
4. Open flip
5. Use Stylus to enter the 10 digit MIN
6. Press OK (No SID entry is required)
7. Programming is complete

TP 5250
1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. The phone display will read SVC Program
5. Scroll to MOBILE PHONE # and press OK
6. Phone display will read Mobile Phone Number
7. Enter the 10 digit MIN and press OK
8. Scroll to Home SID and press OK
9. Enter the 4 digit SID (4654) and press OK
10. Reset Phone will be highlighted. Press OK
11. Phone will reset
12. Programming is complete

LG V111(DM110)
[menu]30.
After ask lockcode, enter: 843691.

Ericsson
Programming:
Shot NAM 987 + menu
Long NAM 923885 + menu and enter SPC: "000000" or may be other SPC typed by user.
CDMA mode 904093 + menu
Analog mode 904095 + menu DM mode 904959 + menu

Hyundai
HGC-120E / -130E programming: #86904**89397#
HGC-600E programming: ##20022002, END and enter SPC: "000000" or may be other SPC typed by user.

Sony
CM-M1300/3300/Z200 programming: type "111111" and press Jog Dial.
Choose "Programming" and enter SPC: "000000" or may be other SPC typed by user.

Sony CM-M1300
1. Power phone on
2. Enter six "1s" ( 111111 )
3. Press the jog dial in
4. Press the jog dial in again to select programming
5. Enter six "0s" for the service security code
6. Phone displays the ESN
7. Press the jog dial in for OK
8. Enter your ten digit cellular telephone number
9. Press the jog dial in for OK
10. Enter your cellular carrier’s system ID (SID) without the zeros
(Example: if your carrier’s system ID is 00035, enter just 35)
11. Press the jog dial in for OK
12. Enter a name for NAM 1 or just press the jog dial in for OK
13. Phone displays Basic NAM 1 Programming is complete
14. Press the jog dial in
15. Press the jog dial in again for EXIT
16. Phone powers itself off
17. Press the power button to power the phone back on
18. Basic programming is complete

Motorola
StarTAC 7760/7860 programming:
Service menu: FCN+0+000000+000000+RCL
Test mode: FCN 00**83786633 STO
V60c programming:
Service menu: 74663 # [Menu] [Menu] (programming code)
Test mode: [Menu] 073887 * (security code = 000000)
Motorola Tarpon (120x)
1. Press 74663 (spells PHONE)
1. Press # MENU MENU quickly
2. Enter OTKSL
3. The work MIN will be highlighted
4. Select the word CHANGE by selecting the top right button
5. Select DELETE. Press and hold the button until clear
6. Have the customer enter the 10 digit MIN number
7. Select OK with the top right button. The “User Activation” screen will appear
8. Scroll to highlight the CDMA Sys ID
9. Select CHANGE by selecting the top right button
10. Enter SID
11. Select OK by selecting the top right button
12. Select DONE with the top left button
13. Press the END key
14. Press # MENU MENU quickly
15. Enter OTKSL
16. The work MIN will be highlighted
17. Select the word CHANGE by selecting the top right button
18. Select DELETE. Press and hold the button until clear
19. Have the customer enter the 10 digit MIN number
20. Select OK with the top right button. The “User Activation” screen will appear
21. Scroll to highlight the CDMA Sys ID
22. Select CHANGE by selecting the top right button
23. Enter SID
24. Select OK by selecting the top right button
25. Select DONE with the top left button
Press the END key
Motorola Phones (ALL)
1. Enter 74663 # FCN FCN
2. Enter OTKSL
3. Enter MIN and press STO
4. Enter SID (4654) and press STO
5. Press STO again – programming is complete
Note: on the Tarpon (120C) you will need to press the MENU key instead of FCN.

Nokia
5185/6185 programming: *3001#12345#
Software version: *#837# or *#VER# or *#9999#
Serial / ESN: *#92772689# or *#WARRANTY#
Phone reset: *#75681# or *#75682#
Nokia 6185-5170
1. Press *#639#
2. Enter OTKSL and press OK
3. Enter the MIN and select OK
4. Enter the SID and select OK
5. Programming is complete
Nokia 3585
1. Enter ## followed by the OTKSL
2. Number (MDN) is highlighted. Press the upper left-hand soft key to select
3. Mobile Number will display. Enter the 10 digit MIN
4. Press OK
5. IMSI will appear. Press and hold the Clear key until the display is empty.
6. Enter 31000 plus the MSID (15 digits total)
7. Press the upper left hand soft key and select OK
8. It will take you back to the SVC Programming. Press the upper right hand soft key to select EXIT
9. Press END.
10. Phone will power cycle and programming is complete.

SK Teletech
SK-IM 1000/1400/2000/2200/2400 programming: #7583538324#626#

Getrun 2000
System NAM programming mode: 0 + 1 + # + 7 + 3 + 7 + SECURITY CODE (000000)
Debug menu: 0 + 1 + # + 3 + 2 + 4 + SECURITY CODE (000000)
Debug screen of field test mode: 0 + 1 + # + 7 + 2 + 7
Test mode: 0 + 1 + # + 7 + 6 + 4 + SECURITY CODE (000000)
System test mode: 0 + 1 + # + 7 + 6 + 8 + SECURITY CODE (000000)

NEOPOINT
Neopoint 1000
1. Press M to display Main Menu
2. Scroll to PREFERENCES
3. Press softkey under SELECT
4. Enter 040793
5. Scroll to PROGRAMMING
6. Press softkey under SELECT
7. Enter OTKSL
8. Press softkey under DONE
9. Scroll to PHONE NUMBER
10. Enter 10 digit MIN
11. Scroll to HOME SID
12. Enter SID (4654)
13. Press softkey under SAVE to exit
14. Programming is complete
NEOPOINT 1600
1. Power the phone on
2. Press the "Menu" key
3. Scroll to "Preferences" - press "Select"
4. Key in the "Field Service Code" (the phone will not prompt you for the code)
at the "preferences" screen to access the "Service" menu (Default code is "000000")
5. Scroll to "Programming" - press "Select" - the phone will ask for the "Subsidy Lock Code"
6. Enter the "Subsidy Lock Code(654321)" to access the "NAM" menu
7. Select the NAM to be programmed (NAM 1 or NAM 2)
8. Program the NAM - Phone number and CDMA Home SID
9. After programming has been completed press "Save" - the phone will reset

Audiovox
Audiovox 9100
1. Press ##
2. Enter the OTKSL
3. Display will read Service/Menu 1 Basic…press OK
4. Next screen will read Service Mode/Home SID…press OK
5. Next screen will read Service Mode/Home SID…press OK
6. Device will display Service Menu 1. Basic #
7. Press END button to complete programming

Handspring TREO
1. Open the flip and press the PHONEBOOK button one time to display the dial pad
2. Enter ## and the OTKSL using the numbers on the Dial Pad
3. Press the handset button shown in the diagram above
4. At the Activations screen enter the MIN in the phone number field using the numbers on the device keyboard
5. Put a check in the Enable Number Portability box and type the MSID in the MSIN field
6. Press OK
7. The device will display the network search pop-up and return to the Phonebook display

Hitachi P300
1. Enter ## and the 6 digit OTKSL
2. Press the Options soft key and then scroll to Save Phone #. Press the OK soft key.
3. At the NAM display scroll to EDIT and press the OK soft key
4. Display will read NAM and MDN will be highlighted. Press the OK soft key.
5. At the MDN display enter the 10 digit MIN and press the SAVE soft key.
6. At the Save prompt press the OK soft key. The next display will show several options that should not edited.
7. Press the EXIT soft key and the device will power cycle.
8. Programming is complete.

Kyosera
Kyocera 2345 1135
1. Press 111111 (#1 key 6 times)
2. Option will be highlighted
3. Press OK
4. Scroll down to Programming
5. The service programming dialog will appear Enter Security Code.
6. Enter the 6 digit OTSKL (code will show as asterisks on screen)
7. Service Options will appear
8. Scroll down to the BASIC NAM1 Info
9. Press OK
10. Select the Phone Number by pressing the OK key
11. Using the keypad enter the 10 digit MIN
12. Press OK
13. Press END to complete the programming
Kyocera 6035
1. Press 1 six times (111111) and select OPTIONS
2. Select PROGRAMMING
3. Open flip
4. Tap the OTKSL on keypad on the screen. Tap OK
5. Tap on the PHONE NUMBER field. Enter MIN.
6. Leave A-KEY blank
7. Enter HOME SID (4654)
8. Tap SAVE & EXIT
9. Tap YES
10. Phone will be in OFF MODE Close flip.
Kyocera 3035
1. Press 111111 (the #1 key six times)
2. Options will be highlighted
3. Press in the navigation key (Navigation key is the button located between the TALK & END key)
4. Scroll to PROGRAMMING using the Navigation key
5. Select PROGRAMMING by pressing in the Navigation key
6. Enter the six digit OTKSL and press in the navigation key
7. SERVICE OPTIONS will appear
8. Scroll down to the Basic NAM1 info
9. Press in the navigation key
10. Clear any numbers that may appear using the “clear” key (arrow key located directly below the navigation key)
11. Select the PHONE NUMBER by pressing in the navigation key
12. Enter the 10 digit MIN select OK by pressing in the navigation key
13. Press END. Programming is complete.
Kyocera 2255
1. Press the 1 key six times (111111) “Option will be highlighted
2. Press OK
3. Scroll down to “Programming” and press “OK”
4. Enter OTKSL and press the navigation key
5. “Service Options” will appear scroll down to the “Basic NAM1 Info”
6. Press OK
7. Select Phone Number by pressing OK
8. Enter MIN and press OK again
9. Scroll to Home SID and press OK
10. Enter SID (4654) and press OK
11. Press END. Programming is complete.
QCP 2035
1. Press 1 six times (111111)
2. Press u key to select OPTIONS
3. Highlight PROGRAMMING and press u key
4. Enter OTKSL
5. ESN will appear press left arrow key to select OK
6. Enter MIN and press з key
7. Press з key again to exit - Programming is complete

Sanyo
Sanyo 4000 4500 4700 5000 6000
1. Press ##
2. Enter the OTKSL
3. Scroll to SAVE and press OK
4. ESN will be displayed – press OK
5. Enter 10 digit MIN and press OK
6. Enter SID (4654) and press OK
7. Press OK twice
8. Programming is complete
Sanyo 5150 5300 and 6400
1. Enter ## followed by the OTKSL
2. Press MENU SAVE PHONE #
3. Press Ok
4. SVC Programming will be displayed. Scroll and highlight Mobile Number. Press OK
5. Press OK again
6. ESN will be displayed. Press OK
7. Mobile Number will be displayed enter the 10 digit MIN press OK
8. Press OK 4 times
9. Phone will power cycle
10. Programming is complete
Sanyo 6000
1. Press ##
2. Enter OTKSL
3. Press MENU Key and scroll to SAVE PHONE # and press OK
4. ESN will be displayed press OK
5. Enter MIN and press OK
6. Enter SID and press OK
7. Press OK twice more
8. Programming is complete
Sanyo 4900
1. Enter ## followed by the 6 digit OTKSL
2. Press the MENU/OK key and scroll and highlight SAVE PHONE #
3. Press MENU/OK
4. Scroll and highlight MOBILE NUMBER press OK
5. At the ESN display press OK
6. In the MOBILE NUMBER screen enter your MIN and press OK 4 times
7. At the service program menu scroll to exit and press the MENU/OK key.
8. Programming is complete
Sanyo 6200
1. Enter ##
2. Enter OTKSL
3. Press the MENU key and scroll to highlight SAVE PHONE #
4. Press OK
5. Scroll and highlight MOBILE NUMBER
6. Press OK twice
7. Scroll and highlight EXIT
8. Press OK
9. Phone will power cycle
10. Programming is complete

Toshiba
Toshiba 2032P
1. Slide the Radio Standby Switch on the left side of the device to the upper side (ON) to activate the phone function. This is the switch with the phone icon over it
2. After power up is completed use the stylus to tap on the ADMIN pull up menu at the bottom of the screen and select ACTIVATION WIZARD. If your device has not yet been activated the ACTIVATION WIZARD will automatically start when you turn on the radio in your device.
3. Tap NEXT 3 times. If the device has been previously activated it will require only 2 presses.
4. On the fourth screen enter the 6 digit OTKSL using keyboard
5. Enter the MIN in both entery fields then tap NEXT
6. Wait for the device to initialize and display “ready to connect”
7. To initiate IOTA tap the word ADMIN at the bottom of the display and then Data Provisioning
8. Programming is complete

*******

Here is a list of various codes to try out. Some may require an MSL to be able to make full use of the functionality.

##2769737 [##BROWSER] - MiniBrowser Settings (2G)
##8626337 [##VOCODER] - Set Vocoder
##3282 [##DATA] - Setup Menu for Vision handsets
##8463 [##TIME] - Airtime Menu
##040793 - Debug Menu
##786 [##RUN] - Technical Information (be careful with this one, you can reset the handset)
##932 [##WEB] - IP Address information (2G)
##889 [##TTY] - TTY On or TTY Off
##4357 [##HELP] - Help

[Inox]

yang nokia mana mang

[willydewi]

Ada kok ..coba di lihat2 lagi

[s_mochamad]

wedew... buat P1 gw ada gk ya

[willydewi]

Originally Posted by s_mochamad

wedew... buat P1 gw ada gk ya

emang nggak ada ya di dalam2 kode2 di atas itu ..kalo emang kagak ada ,ntar di cariin deh

[Inox]

Originally Posted by willydewi

Ada kok ..coba di lihat2 lagi

iya mang...ada :malu:


Ijin Save As yaa

[willydewi]

sip di lanjut


ini ada trik lagi

To hard reset a HP iPAQ 112
1. Press Win + OK + Record together
2. While doing that, press reset button and hold for 3-4 seconds
3. Release reset
4. Release buttons
The screen shows "CLEAN REBOOT"

[willydewi]

Unlock bb5 SECURITY CODE

Berikut Tips untuk buka security code dengan menggunakan memory card pada HP Nokia BB5 dan ada beberapa type Nokia yg laen juga bisa dengan cara ini :

1. copy paste kan file yg di download di bawah ke dalam dalam memory card di direktory E:\system\recogs

2. kemudian masukan memory card ke dalam HP yg terkunci tersebut

3. Hidup kan HP dan biar kan hidup selama 3 menit ( jangan lakukan apa2..cukup di lihat aja sambil hidupkan sebatang rokok )

4. kemudian setelah 3 menit ..Buka batre keluarkan memory card

5. hidupkan kembali HP kamu ...selamat code nya telah berubah kembali ke standar yaitu : 12345


Note: beberapa antivirus menganggap file ini virus..tapi bukan loh

Download :

 

http://w14.easy-share.com/1700987350.html

[azzavirtium]

wah maknyus banget nih....ane ijin copas ye.

thanks

[mbregadjul]

gak bisa donlod bos? file not found????
mohon pencerahannya.... membantu bgt nih kalo bisa....
thanks...